Showing posts with label Velocette engine. Show all posts
Showing posts with label Velocette engine. Show all posts

Monday, June 29, 2015

The dynamometers at Velocette......

The dynamometers at Veloce Ltd. 
With thanks to Hedley Cox and Dai Gibberson.


Over the years I've researched the dynamometers used at Veloce for the testing of their Velocette engines. 
They never had a rolling road type dyno so power at the rear wheel was never tested. 
Much of the information we have for certain comes from after 1938 when Velocette built a new test house. 
It is pictured, below when opened by Stanley Woods the factories then senior contracted road racer.. 


Pictured is Stanley woods, with wife Mildred by his side and the giant key for publicity. In the white lab. coat is Harold Willis the race team chief and development engineer, sadly to die a year later. The managing director, Percy Goodman's head is just visible over Stanley's shoulder.
 Following the opening of the new test house, the camera moved inside for a pic of Stanley "operating" the throttle of the dynamometer with a factory 350cc SOHC race engine on test. Harold Willis and Percy Goodman look on.
I've formed the opinion that there was only one dynamometer at Veloce before the new test house which when opened contained three. This early Hennan and Froude dyno had a calibration factor of 5500. The comment below is from 1930 and is by Phil Irving in his autobiography, p.160.



 Phil Irving's Autobiography is a mine of information on what happened at Veloce 1930-1943.... regretably the costs of his out of print book today on Amazon and others is in the $1000 range...perhaps a good library may have one to peruse...
The other two dynos installed  in 1938 were new Heenan and Froude DPX2 dynamometers with a calibration factor of 4500.
What does this calibration factor mean?
These Heenan and Froude dynos were called “water brakes” and utilised hydraulic principles with the power developed by an engine on test being measured in the pull on a spring gauge of pounds (lbs).
So the dyno operator..at Veloce, Tommy Mutton, Frank Panes, Hedley Cox,Freddie Owen, Jack Passant etc…would record pull of the dyno in lbs at a given engine rpm and record the barometric pressure and temperature in the room, which was assumed to be the induction air temperature.
This was recorded in a small notebook and occasionally it would show the uncorrected bhp, that is, not corrected for the air temp. and barometric pressure of the day.
The formula was….

uncorrected bhp = rpm x pull in lbs
                                                dyno constant

 As mentioned, early on 5500 then from 1938 on the new dynos, 4500.
an example for say 1939 at Veloce for a factory 500 is....
uncorrected bhp =6250 x 34.6
                                                   4500
                                         =48bhp
Sectioned 1939 Heenan and Froude DPX2 dynamometer


When Heenan and Froude introduced the DPX2 dyno and Veloce bought two for the new test house, the constant was 4500. The new dynos were called the “centre bench” and it was used for the testing of the works racers and the model KTT, the other was specially setup for the new Roarer engine under construction and pictured elsewhere in this post. The old 5500 dyno was called the “end bench”.

Following WW2 in 1949 the “end bench” was replaced by a new DPX2 dyno by Hedley Cox and the old “end bench” scrapped. 
Up to then following the war the “end bench” had been used for running in new mk.8 KTT engines.

During WW2 Phil Irving used this bench to test special MAC and MSS engines for military use.
 The Roarer engine on the test bench during 1939.
The Roarer engine on the way to the test house during early 1939.
Final construction of the Roarer in time to send over to the 1939 IOM TT where it only completed one lap in practice and was replaced by the normal factory 495cc SOHC  racer. Pictured is, left Percy Goodman, Tommy Mutton on the bike and  Harry Thorne.
Tommy Mutton about to start a test of a mk.8 KTT engine on the centre bench  in 1939. The mk.8 KTT engines started at engine nos. KTT801


Tests conducted by Phil Irving in 1940 on 495cc MSS engines for coming  military trials, using the older end bench with the 5500 constant.Details from PEI's notebooks of the time.

Following WW2, racing recommenced in 1946 and Velocette re-introduced their prewar factory racers and continued with the mk.8 KTT, which commence with engine number KTT901
Tommy Mutton continued as the senior race mechanic until around 1948 when following disagreements with Charles Udall, then the development engineer he asked to be transferred to another section of the factory. 
He is pictured below in 1947 with Chas. Udall and a factory SOHC 350 on test on the centre bench.
In 1948 Hedley Cox joined Velocette as a race mechanic and details from his lastest book "A Guide to Motorcycle Racing" published in June 2015, p.19,20 the setup in the Test House at that time....
During 1949 the old end bench which Hedley described as worn out and which had only been used to run in mk.8 KTT engines assembled by himself, Frank Panes and Freddie Owen was dismantled by Hedley and replaced by a new Heenan and Froude DPX2 dynamometer...
Very similar to the prewar design....pictured is a 1960 version.

Following Frank Panes leaving Veloce for New Zealand and Hedley Cox's sacking by Bertie Goodman in 1952, Freddie Owens and a new man, Jack Passant were responsible for the last gasps of the Velocette race effort and the cessation of production of the mk.8 KTT.
Jack Passant went on to become the Development engineer up to the factories liquidation and closure in February 1971.
During this time he further developed the MSS and the Venom and was responsible for the  Venom Thruxton engine.
 Veloce supplied several to teams in the 1967 IOM TT 500cc Production machine race, won by Neil Kelly on a machine entered by the London dealers L.J. Stevens.
A Venom on the centre bench starting a test...
Jack Passant with a Venom Thruxton engine on test
The special VMT engine returned to Velocette after its win in the 1967 500cc class of the production machine race...Jack had it on the test bench....Unsure why there is no reading for 6200rpm, but the uncorrected bhp at 6000rpm is 40bhp.
Neil Kelly winning the 1967 500cc class of the IOM production TT...photo courtesy of Bill Snelling, TT fotofinders.


Sunday, December 21, 2008

Squish head Velocettes.......

I wrote the following for the current owner of the late Keith Smith's special squish cylinder head racing Velocette.....
Included are letters from the 1960s to Bertie Goodman of Velocette and photos of interest, including the photograph I had professionally taken of the cylinder head and piston to send to Veloce Ltd.
Left click to enlarge the images....
From memory either Sid Lawrence or a chap in Melbourne, whose name escapes me at present both developed a squish head Venom in the early 1960s.
I am unsure if it was as a result of speaking to each other or they came upon the idea independently.
Basically the engine was a pushrod version of a late1950s/early 1960s Manx Norton in combustion chamber shape and piston profile.
The Manx Norton squish idea was developed by the Polish engineer, Leo Kusmicki, who initially worked at Norton as a cleaner I believe immediately following WW2 in which he was a Spitfire pilot in the Polish Airforce, but came to the attention of Joe Craig who utilised him in the race shop and many believe used his ideas as his own. Certainly Kusmicki rarely featured in the press and seems unknown to many people, including Norton enthusiasts.
Eric Hinton knew him from the time the Hintons were involved with Norton racing in UK and Europe and Eric told me Leo was the brains behind Nortons racing success once the squish engines were developed.
The squish head used by Norton and the three Velocettes in Australia, all had machined deep lands in the hemispherical combustion chamber. See the photograph of the Velo head, taken by me at CSIRO, Division of Animal Physiology, Prospect, NSW in 1964.
The piston has opposite lands on it and goes into the cylinder head to almost make contact with the head at these lands.
The most effective gap between piston and cylinder head over these lands is around 0.035”.
The so called squish clearance.
Too little and in operation the piston will hit the head, too little and the squish effect becomes lost.
After we photographed the squish Velocette head, we sent a photograph with a letter to Bertie Goodman, then Sales Director of Veloce Ltd.
Years later he replied that they had used this idea in a batch of 12 special engines built for the Velocette Venom Thruxton.
In fact the L.J. Stevens sponsored Thruxton that won the 500cc class of the Production TT in the IOM in 1967 used one. The head resulted in an additional 4½ bhp from the engine.
My involvement was with the late Keith Smith.
Keith ordered a new Velocette Venom Clubman Veeline( called a Mk.1 version now) in late 1963 from the then Velocette agent in NSW, Hazell & Moore Pty. Ltd.
Few Velocettes were sold in NSW from around 1960 when the then State Government made what to motorcyclists were draconian alterations to the compulsory Third Party Insurance on motor vehicle registrations. Bikes over 250cc were particularly disadvantaged with large premium increases.
I can’t remember the figures now, but 350cc machines and most 500cc machines disappeared overnight. Few were imported. Victoria and other States were different and Frank Mussett Motorcycles in Melbourne, Victoria continued to sell Velocettes ok.
Keith took delivery of his new Clubman in the packing crate as it was sent from Veloce Ltd in early 1964.
I was at his house when they arrived from the docks and we excitedly opened the crate. To reduce the freight volume, the wheels had been removed and bolted to the inside of the crate near the top. Somebody in the packing section at Veloce had nailed the lid on and the nail went offset and into the tyre, so we had a puncture before we even started!
Then..Hazell & Moore were really reluctant to accept the problem and only wanted to patch the tube!! After we just bought a new motorcycle off them…
Keith rode the bike on the road briefly before he decided he would convert it into a road racer.
He was very friendly with Sid Lawrence, who I mentioned earlier had developed a squish cylinder head. Sid was extremely secretive over it and I recall if he had to remove the cylinder head from the bike in the pits at a race meeting he had a large canvas cover that he spread over the bike, crawled under it and worked there in the semi dark and heat in the Australian summer so prying eyes didn’t get a look….
Somehow Sid revealed the details to Keith who machined the head to Sid’s dimensions, we fitted valves into the head and poured bees wax into the combustion chamber to make a mould of it. Then took the mould to Sid Willis, ex successful Velocette racer from the 1950s who was “Mr piston” in NSW and Sid cast a special piston to utilise.
We fitted the head and left the next weekend on a shakedown ride to northern NSW, myself on my 1958 MSS.
The bike was plagued with overheating problems, pinged etc. In desperation at Armidale we found an old chap with a workshop and fabricated a thick copper head gasket and limped back to Sydney.
The problem was the ignition timing we were using.
Never having done this before and not finding out what Norton used, we used the 38° BTDC recommended by Veloce for all Venoms.
However with the better combustion efficiency we were able to come back to 28° BTDC and all was well.
Sid Lawrence was an A grade rider ( Australia used a grading system then for racing in all classes. The top riders were “A”, then “B” and “C” ). Keith was a “B” grader and enjoyed success on his Velocette. Sid Lawrence would regularly finish in the top 4 or 5 positions in the title races he contested.
Handling of the Velocette frame was inferior to the Norton “Fetherbed”.
At Bathurst, west of Sydney, NSW, which then had a slightly downhill straight of 1¼ miles long, the squish head Velo was timed at 134mph, Manx Nortons and G50 were in the 132-136mph range during title races.
Keith’s squish Velo from memory was timed at 128mph.
Tragedy struck shortly after with Keith’s untimely death while riding his brothers 7R AJS special at a private practice session at the Oran Park motor racing circuit south of Sydney.
The motorcycle was used on occasions by his brother Terry in conjunction with the 7R, but he soon retired from racing and the bike was sold to Ken Wall of Torquay in Victoria.
Ken rode it on occasions, but with no major success and just before his eventual death it was sold on to Velo club member John Davies with a broken crankcase.

The first photo is of the cylinder head and piston sent to Veloce Ltd., with the first letter illustrated.

The second letter ( 2 pages ) is a reply from Bertie Goodman as is the third letter ( also 2 pages)

The second photograph is taken at Bathurst NSW, Easter 1964 races, myself to the left and Keith Smith to the right behind his now drastically modified Venom Clubman.

The last photo shows Keith at Oran Park circuit in 1966, shortly before his death.

Saturday, November 22, 2008

The 700cc twin cylinder MAC Velocette that never was....

In the 1950s an innovative young engineer, Allan Russell of Sydney, a Velocette enthusiast and assistant to the late Sid Willis, champion Aussie 250 class road racer on Velocettes, started to build a twin cylinder MAC Velocette engine, SOHC valve operation and made many of the casting patterns needed, then cast the cylinder heads, cambox, bevel box, prepared drawings of two ways to drive the overhead cam gear from the MAC timing chest.



Then he fell in love, married Margaret ( they are still together...) ,all work on the MAC ceased and the MAC engine languished in a large drawer in his workshop for over 50 years.




I'd briefly seen the drawer pulled open in the 1960s to illustrate a point in a discussion, but it stayed there until 2005, when my best friend, Velo enthusiast Jim Day suggested we ask Allan to get it out and we would feature it on a display table during the final night meeting at the Australian Velocette Centenary Rally at Richmond, west of Sydney.
Prior to it's return to Allan, we assembled it and I photographed it...

Where is it now....?

Back in Allan's drawer....awaiting the time Allan can find to continue with it....

Interesting "bit of kit" as they say...

Left click on photographs to enlarge....